more information, market research, kodak goldweb directory, tripods, tamron | ||
photo album, creation studio, shop pro, sherwin williams, with npca | ||
MEDICINE - Internal Medicine Doctor, Natural Medicine | ||
|
| This article does not cite any references or sources. (September 2007) Please help improve this article by adding citations to reliable sources. Unverifiable material may be challenged and removed. |
The Boxer engine, first patented by German engineer Karl Benz
UL260i flat-4 aircraft engine
A flat engine or horizontally-opposed cylinder engine is an internal combustion engine with pistons that are all relatively horizontal. A straight engine canted 90 degrees from straight up is a flat engine, as is one in which the cylinders are arranged in two banks on either side of a single crankshaft. In both configurations, the motion of all the pistons is in the horizontal plane.
German engineer Karl Benz patented his design for the first internal combustion engine with horizontally opposed pistons in 1896.
Usually, each pair of corresponding pistons from each bank of cylinders share one crank pin on the crankshaft, either by master/slave rods or by two ordinary rods side by side. Some authorities divide flat engines into boxer engines which do not share crank pins in this way, and 180° engines which do.
Contents |
Flat engines are shorter than in-line engines, and have a lower center of gravity than any other common configuration. Automobiles and motorcycles powered by a flat engine generally have a lower center of gravity, giving better stability and control. These engines, however, are also wider than more traditional configurations and are more expensive to build. The extra width may cause problems fitting the engine into the engine bay of a front-engined car owing to the interference with the steering wheels, and create cornering problems for a motorcycle.
The flat configuration also fits very well with air cooling and aircraft engines. Air-cooled designs such as in the VW Beetle used a flat-4, as did the Porsche 356 and 912. The Chevrolet Corvair used an air-cooled flat-6, a rarity in American designs. Both the older and newer models of the 911 use a flat-6, at first air cooled but later models are water-cooled. These automobiles situate the engine in the rear rather than the front, where its width does not interfere with the steering of the front wheels.
Front-mounted air-cooled flat-twin engines were used by Citroën in their model 2CV and its derivatives, while the Citroën GS used a flat-4, and a flat-6 was proposed for the Citroën DS, but rejected. BMW uses an air-cooled or partially oil-cooled flat-twin in many of their motorcycles.
All versions of the Subaru Impreza, Forester, Tribeca and Legacy use either a flat-4 or flat-6 engine.
Boxer engines probably got their name because the pistons of the motor, when observed from the top, resemble the fists of a boxer pummeling his opponent. Boxer engines of up to eight cylinders have proved highly successful in both automobiles and motorcycles, and continue to be popular for light aircraft engines.
One benefit of using a boxer engine versus a V-engine is that the design provides good balance because each piston\'s momentum is counterbalanced by the corresponding piston movement of the opposite side. Boxers are one of only four layouts that have a natural dynamic balance; the others being the straight-6, the V12 and the wankel engine. These engines can run very smoothly and free of vibrations with a four-stroke cycle and do not require a balance shaft or counterweights on the crankshaft to balance the weight of the reciprocating parts, which are required in other engine configurations. Note that this is generally true of boxer engines regardless of the number of cylinders, but not true for all V and straight, or inline engines. However, in the case of two-cylinder boxers, a small "rocking couple" imbalance is unavoidable. This is a consequence of the "opposite" cylinders being not exactly opposite but offset slightly.
Boxer engines tend to produce more noise than inline and V-engines because valve clatter is not so well dampened due to lack of covering by air-filters and other components, and produce a larger torsional vibration than a V-engine, and so tend to require a larger flywheel. They have a characteristic smoothness throughout the rev range and, combined with the mounting position immediately ahead of the rear axle, offer a low center of gravity and more neutral handling.
|
|
This article or section contains information about scheduled or expected future events. It may contain tentative information; the content may change as the event approaches and more information becomes available. |
Flat V engines are used in performance and racing cars, normally a 180 degree V12. Ferrari used a 180° version of the Colombo V12 in the Testarossa and Berlinetta Boxer models.
| | This short section requires expansion. |
| Reciprocating engines and engine configurations | |
|---|---|
| Straight | Single · 2 · 3 · 4 · 5 · 6 · 8 · 9 · 10 · 12 · 14 |
| Flat | 2 · 4 · 6 · 8 · 10 · 12 · 16 |
| V | 2 · 4 · 5 · 6 · 8 · 10 · 12 · 16 · 20 · 24 |
| W | 8 · 12 · 16 · 18 |
| Other inline | H · U · Square four · VR · Opposed · X |
| Other | Hemi · Radial · Rotary · Pistonless (Wankel) |
|
|
This article or section includes a list of references or external links, but its sources remain unclear because it lacks in-text citations. You can improve this article by introducing more precise citations. |
This article is licensed under the GNU Free Documentation License. It uses material from Wikipedia